More 1934 Transmitter

I've gotten the components all mounted and the transmitter is ready for wiring. I learned a few things along the way...

30s vintage Sangamo mica capacitors are large enough that they don't mount well on their own leads. Each one must be mechanically supported, either by a solder strip or by screwing to the wooden sides of the chassis.

The wooden chassis takes 1 1/2 inches of available length and width. This can impact the layout. Using an all metal chassis there is space for a buffer stage between the oscillator and amplifier. With 1 1/2 taken off the length/width plus the added reinforcing across the middle it would be a challenge to fit the buffer stage in there.

Will the lead length be a problem? Certainly I wouldn't trust this spread out layout at 30MHz but it may be OK on 7MHz. Time will tell.

QRP from Frontenac State Park

Sunday afternoon, July 5, I got over to Frontenac State Park for some picnic table QRP. The picnic area there sits at the edge of a 400' bluff over looking the Mississippi River. Below the park is Lake Pepin , a naturally wide part of the upper Mississippi. To the east, across the Mississippi/Lake Pepin, is Wisconsin. The weather Sunday was sunny but not too warm in the shade, perfect for picnic table QRP.

Using my K1 running 4 watts and feeding a 67' end fed wire I worked K4BAI(Columbus, GA), WA3PAK(Marion, OH) and N7JOX(northern CO near Cheyenne, WY). All in all a satisfying and relaxing afternoon....

More 1934 Transmitter

After some quality table saw time, a bunch of drill press time and eight coats of paint (primer coat, satin black, three coats of wrinkle paint that didn't wrinkle and three more coats that did) I have a wood and aluminum chassis that looks pretty good. The layout is much like the Gross CW-25 but without the buffer stage. In place of the middle/buffer tuning dial I'm mounting a plate current meter. Across the bottom are three 1/4" phone jacks. One is the key jack. The other two are in the B+ circuits of the oscillator and final amp stages. These two jacks will have 350VDC exposed on the outside rim. For safety I recessed these jacks 1/2" behind the front panel. I also added a B+ switch on the far right.

I found two more examples of this tube lineup. One is a George Grammer construction project covered in November 1932 and February 1933 QST. The second is the Collins 4A transmitter.

More 1934 Transmitter

After collecting all of the parts comes "playing checkers" to find the best layout given the set of parts located. In this case I found suitable 30's parts for all of the major components except the chassis itself. For it I'm using a 17"x10" sheet of 18 gauge aluminum. It will be fastened to a 4 1/2" tall wooden frame and then frame and aluminum painted black winkle.

A 1934 Style Transmitter

Since the AWA Linc Cundall OT CW Contest in January I've been thinking about building another transmitter, this one falling in between my 1929 TNT transmitter and my Thordarson 100 or late 30's 6L6 transmitters. I want to use it with my National FB-7 so it needs to be an early to mid 30's design.

A popular design in the early 30's used a type 47 as a crystal oscillator driving a buffer and final on 160 through 10 meters. Typical power was anywhere from 20 watts on up depending on the tube lineup. The Gross CW-25 was one example. It had a 47 oscillator driving a 46 buffer/multiplier followed by two 46s in parallel. Plug-in coils were available for all bands 160 - 10. This looks like a pretty neat transmitter. More about the CW-25 can be found in Bill Orr's "Antennas" column in the February 1977 issue of CQ magazine.

I wish I could find a CW-25 available. Does anyone have one they will part with? In the mean time I'll have to homebrew something.

The cover story of the November 1971 issue on CQ magazine is a Bill Orr construction article describing a 160/80/40 meter "1934 Style Transmitter". Circuit-wise it is a close match to the CW-25 but without the buffer/multiplier stage. This circuit design fits my early/mid 30's requirement but the CW-25 chassis sort of construction better matches the "modern" look of my FB-7. I'll combine the two using the circuit from Bill Orr's article but building it to look more like the CW-25.

Notice that the schematic scanned from the original CQ article is missing the connection between the coupling capacitor C6 and the 46 tube grids.

QRP FYBO Contest

Today I participated in the annual QRP FYBO (Freeze Your B___ Off) contest. See http://www.azscqrpions.org . It happened that we are into a little warm spell after several weeks of below freezing weather. The temperature was 40 at 10AM when I got started, rose to 46 around lunchtime and then dropped into the 30s by the time I got off the air at 3:15. I'm not a big contester. With on and off operating and marginal band conditions I made only 5 contacts on 40 and 20 CW for 800 points. Most hams I worked were relatively warm, only VE3RRP in Ontario was below freezing.

The FYBO Contest did give me a chance to get out of the basement shack. One of the neighbors interrupted a snowman build to find out why I was lounging on my deck in February. Even with temperatures hitting the mid 40s it is still winter in Minnesota.

I found the FYBO Contest a challenging and fun break from my regular winter boatanchor activity. I'll do it again next winter.

AWA Linc Cundall OT CW Contest (Part 2)

The second half of the AWA Linc Cundall OT CW Contest was this past weekend. Between Saturday evening and Sunday afternoon I added 4 contacts to my log including W0LGU(MN), WA9QNN(WI), WB9WHG(MN) and NG9D(IL). While not a lot of contacts this year my push-pull 6L6 transmitter seemed to work pretty well. I suspect my low antenna (only 10-15ft off the ground) resulted in a lot of RF going straight up. I did OK for nearby stations but heard/worked no east coast stations.

AWA Linc Cundall OT CW Contest

The first half of the AWA Linc Cundall OT CW Contest ran Wednesday evening through Thursday late afternoon. This coming Saturday is the second half of the "contest".

My station this year is a 1938 vintage NC-101X and a homebrew crystal controlled push-pull 6L6 oscillator. Electrically this transmitter is based on the QSL Push-Pull in QST, June 1940. I added cathode current metering, a load control and regulated the screen voltage to 150V. I ran mine with only 300V on the plates for about 20 watts input and around 10 watts output on 80 and 40. Cosmetically this transmitter is based on what I had on the shelf to work with, an old amplifier build in an even older Meissner Signal Shifter cabinet.

Here in SE Minnesota using my low hung 105' inverted "L" antenna I heard no AWA stations on the air Wednesday night but did work W0NYQ(MN), KB0ROB(MN), VE3AWA(OT) and AA9DH(IL) late Thursday afternoon.

An Iambic keyer rated for cathode keying

When using my vintage transmitters I've missed not having a keyer. Many older tube transmitters are cathode keyed. The voltage across the key terminals can be high enough to fry the output transistor of a typical modern keyer. In some cases the voltage can even be high enough to be a safety problem.

I already had a K1EL K10 keyer board ( http://k1el.tripod.com/K10.html ). I added a Keyall from Jackson Harbor Press ( http://wb9kzy.com/keyallhv.htm ) to make a keyer capable of keying up to 500V. It works great! I even installed a jack for a straight key so that I use the K10 CW monitor plus the Keyall isolator on Straight Key Night.

1929 AWA QSO Party

The last two weekends I participated in the AWA 1929 QSO party. The main requirement is that the transmitter be a 1929 or earlier design. I ended up using my two tube TNT (tuned plate - not tuned grid) transmitter (see http://www.io.com/~nielw/tnt/tnt.htm ) while the receiver was a National SW3 three tube regen (see: http://www.io.com/~nielw/nat_list/sw3.htm ). See http://www.io.com/~nielw/1929Stn/1929Station.htm for more information and videos.

I was only on 80 and worked 8 stations, 7 in MN and one, WA3FFC, in PA. MN contacts were W0DGU, K0KCY, W0CWU, WA9WFA, W0NYQ, K0PK AND KB0ROB.